"single inlet single width centrifugal fan"

Alloy Steel Coupling Driven Energy Saving Forced Draft Boiler Fan Introduction 1.It can output higher outlet pressure and provide more gas flow at the same time, low noise. Stable operation at higher media temperatures. 2. The fan speed can be flexibly set by matching different belt pulley diameters to make the fan run at the highest efficiency point and reduce energy waste. 3. Motor slide guide can be provided for convenient belt tensioning to reduce energy loss caused by

Alloy Steel Forward Anti-Explosion Industrial FD High Temperature Boiler Fan Introduction Medium requirements for 6-08 series fans: The medium to be transported should be non-corrosive, non-flammable, explosive, and free of viscous substances. The dust and hard particles contained in the medium should be no more than 150mg/m3. Medium temperature: The medium temperature of standard fans is not more than 80 °C, the V-belt driving type fan can transport media below 150 °C for a

Double Suction Industrial High Temperature Medium Pressure Boiler Fan Introduction Of Centrifugal Fan This type of fan is currently used in the boiler industry. The air volume of the induced draft fan and the difference in wind pressure are relatively large, in order to adapt to the above situation, considering the practicability of the fan, in addition to the 20-ton boiler ID fan need large power coupling direct transmission, the other uses the triangular belt type

Aluminium Alloyed Forward Industrial Kilns Induced Draft Fan Introduction Of Centrifugal Fan 6-04 series fans have high pressure coefficient, low peripheral speed, low noise, flat performance curve and wide area of high efficiency. Bearing cooling method: according to gas temperature and operating environment conditions choose low-cost water-cooling method or oil-cooling method with good heat dissipation performance. For extremely high temperature operating conditions, can

Q235 Energy Efficiency Backward Flue Gas Fan Radial Fan Blower Introduction Of Centrifugal Fan G4-10 and Y4-10 series ventilation and induced draft fans are suitable for the ventilation and induced draft fan systems of 2~670T/h steam boilers in thermal power plants. They can transport clean gas, dusty gas, flammable gas, corrosive gas, powder or granular materials at normal temperature or high temperature. The weld of the impeller and the main shaft are ultrasonic flaw

Low Pressure Coupling Driving Antifraying Industrial Boiler SA Centrifugal Fan Introduction The 4-14 series centrifugal fan is suitable for indoor ventilation in general factories and large buildings. It can be used to input gas as well as to output gas. The gas delivered by the 4-14 series fan should be no more than 80 °C air and other gases that are not self-igniting and are not harmful to the human body and are not corrosive to steel materials. No viscous substances are

High Air Flow Low Pressure Backward Industrial Boiler PA Centrifugal Fan Introduction 1. The air damper can be used to flexibly adjust the pressure and flow of the fan during operation. It is also possible to select a variable frequency motor, with adjust the pressure and flow of the fan by changing the speed. 2. For the material of impeller and main shaft, we will choose high-strength carbon steel, low-alloy steel, high-temperature alloy steel, high temperature resistant

HG785 Alloyed Steel High Temperature Exhaust Centrifugal Fan Introduction 9-03 series fan-type iron furnace special high-pressure centrifugal fan, is suitable for IL/h, 2L/h, 3L/h, 3L/h, 7L/h melting rate of iron furnace blast performance requirements. The fan can also be used as the blast for various furnace forging furnaces. It is also suitable for conveying air and non-corrosive, non-self-igniting, non-viscous materials or light powder/debris/short fiber materials. It is

Product description The 6-11 series have the characteristics of high efficiency, flat performance curve, wear resistance, and work stability. It has excellent performance and can output high pressure. It can be used to transport normal temperature or high temperature non-flammable gases, particles, powder, debris, fibrous materials etc. The fans are commonly used in large-scale industrial systems such as large dust removal systems, industrial desulfurization and denitrificati